APL5501-2-3b1

来源：尚车旅游网

APL5501/2/3

Low IQ, Low Dropout 500mA Fixed Voltage RegulatorFeatures

• Low Noise : 50µVRMS (100Hz to 100kHz)• Low Quiescent Current : 50µA (No load)• Low Dropout Voltage : 170mV (@500mA)• Very low Shutdown Current : < 0.5uA• Fixed Output Voltage : 1.3V ~ 3.4V• Stable with 4.7uF Output Capacitor

• Stable with Aluminum , Tantalum or Ceramic Capacitors .

• Reverse Current Protection• No Protection Diodes Needed• Built in Thermal Protection

• Built in Current Limit Protection

• Controlled Short Circuit Current : 150mA• Fast Transient Response• Short Setting Time

• SOT-23-5, SOT-, SOT--5, SOT-223, SO-8 ,TO-252 and TO-252-5 Packages

TAB is GND

Design with an internal P-channel MOSFET passtransistor, the APL5501/2/3 maintains a low supplycurrent, independent of the load current and dropoutvoltage. Other features include reverse currentprotection, thermal-shutdown protection, current limitprotection to ensure specified output current and con-trolled short-circuit current. The APL5501/2/3 regu-lator comes in a miniature SOT-23-5, SOT-, SOT--5, SOT-223, SO-8, TO-252 and TO-252-5packages.

Pin Configuration

APL5501

BPGNDSHDN51

4231VINGNDVOUTVOUTGNDVIN

Applications

• Notebook Computer

• PDA or Portable Equipments

• Noise-Sensitive Instrumentation Systems

SOT- (Top View)

SOT--5 (Top View)

INGNDGNDSHDN12348765OUTGNDGNDBYPVIN15VOUT

GND2SHDN34BPGeneral Description

The APL5501/2/3 is micropower, low noise, low drop-out linear regulator. Operate from 2.7V to 6V inputvoltage and deliver up to 500mA. Typical output noiseis just 50µVRMS with the addition of an external 0.1µFbypass capacitor in BP pin and typical dropout volt-age is only 170mV at 500mA loading . Designed foruse in battery-powered system, the low 50uA quies-cent current makes it an ideal choice.

SO-8 (Top View)

GND

SOT-23-5 (Top View)

VOUTBPGNDSHDNVIN

TAB is GND123

VINVOUT

TO-252 (Top View)TO-252-5 (Top View)

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advisecustomers to obtain the latest version of relevant information to verify before placing orders.Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

www.anpec.com.tw

12345APL5501/2/3

Pin Configuration (Cont.)

APL5501

TAB is GND

APL5502

TAB is VIN

APL5502

TAB is VIN

APL5502

SHDNVIN12348765GNDGNDGNDGND

123

VOUTBPVINGNDVOUTGNDVINVOUTGNDVINVOUT

SOT-223 (Top View)SOT- (Top View)SOT-223 (Top View)SOP-8 (Top View)

Ordering and Marking Information

APL5501/2/3 -Lead Free CodeHandling CodeTemp. RangePackage CodeVoltage CodePackage Code B : SOT-23-5 D : S OT- D5 : SOT--5 U : TO-252 U5 : TO-252-5 V : SOT-223 K : SO-8Temp. RangeC : 0 to 70 CHandling CodeTR : Tape & ReelVoltage Code :13 : 1.3V ~ 34 : 3.4VLead Free Code L : Lead Free Device Blank : Original Device°APL5501/2/3 - 13 D/V/K :APL5501/2/3XXXXX13 13APL5501/2/3XXXXXXXXXX - Date Code , 13 - 1.3VAPL5501/2/3 - 13 U :XXXXX - Date Code , 13 - 1.3V Marking Information

SOT-23-5 packageProduct NameAPL5501-13BAPL5501-14BAPL5501-15BAPL5501-16BAPL5501-17BAPL5501-18BAPL5501-19BAPL5501-20BAPL5501-21BAPL5501-22BAPL5501-23BAPL5501-24BAPL5501-25BAPL5501-26BAPL5501-27BMarking517X518X519X51AX51BX51CX51DX51EX51FX51GX51HX51IX51JX51KX51LXProduct NameAPL5502-13BAPL5502-14BAPL5502-15BAPL5502-16BAPL5502-17BAPL5502-18BAPL5502-19BAPL5502-20BAPL5502-21BAPL5502-22BAPL5502-23BAPL5502-24BAPL5502-25BAPL5502-26BAPL5502-27B2

Marking527X528X529X52AX52BX52CX52DX52EX52FX52GX52HX52IX52JX52KX52LXProduct NameAPL5503-13BAPL5503-14BAPL5503-15BAPL5503-16BAPL5503-17BAPL5503-18BAPL5503-19BAPL5503-20BAPL5503-21BAPL5503-22BAPL5503-23BAPL5503-24BAPL5503-25BAPL5503-26BAPL5503-27BMarking537X538X539X53AX53BX53CX53DX53EX53FX53GX53HX53IX53JX53KX53LXwww.anpec.com.tw

APL5501/2/3

Marking Information (Cont.)

SOT-23-5 packageProduct Name Marking Product Name Marking Product Name Marking APL5501-28B 51MX APL5502-28B 52MX APL5503-28B 53MX APL5501-29B 51NX APL5502-29B 52NX APL5503-29B 53NX APL5501-30B 51OX APL5502-30B 52OX APL5503-30B 53OX APL5501-31B 51PX APL5502-31B 52PX APL5503-31B 53PX APL5501-32B 51QX APL5502-32B 52QX APL5503-32B 53QX APL5501-33B 51RX APL5502-33B 52RX APL5503-33B 53RX APL5501-34B 51SX APL5502-34B 52SX APL5503-34B 53SX The last character “X” in the marking is for data code.

Pin Description

PIN I/O Description No. Name 1 VIN I Supply voltage input. (Note1)Shutdown control pin, low = off , high = normal. Don’t leave SHDN I 3 open. Ground pins of the circuitry, and all ground pins must be 2 GND soldered to PCB with proper power dissipation. (Note1)4 BP O Bypass signal pin in fixed output type device 5 VOUT O Output pin of the regulator. Note1: These pins do not exist in 3-pin package.

Absolute Maximum Ratings

Symbol Parameter VIN, VOUT Input Voltage or Out Voltage SHDN Shutdown Control Pin Rating Unit 6.5 V 6.5 V SOT- : 180 SOT-223 : 135 SO-8 : 150 SOT-23-5 : 260 SOT- : 38 SOT-223 : 15 SO-8 :20 SOT-23-5 : 130 Internally Limited 0 to 125 0 to 150 -65 to +150 260 RTH,JA Thermal Resistance - Junction to Ambient °C/W RTH,JC PD TJ TSTG TL Thermal Resistance - Junction to Case Power Dissipation Operating Junction Temperature Control Section Power Transistor Storage Temperature Range Lead Temperature (Soldering, 10 second) 3

°C/W W °C °C °C www.anpec.com.tw

APL5501/2/3

Electrical Characteristics

Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF,SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C.

Symbol APL5501/2/3 Unit Parameter Test Conditions Min. Typ. Max. VIN Input Voltage VOUT Output Voltage ISHORT Short Current IOUT Load Current REGLINE Line Regulation REGLOAD Load Regulation (Note2) 2.7 6 V VOUT+1.0V< VCC<6.0V, 0mA< IOUT < IMAX VOUT -2% VOUT VOUT +2% V VIN=4.3V ILIMIT Circuit Current Limit 0.7 A VOUT=0V VOUT+0.5V< VCC<6.0V, IOUT = 1mA VIN =VOUT+1.0V, 0mA< IOUT < IMAX 1.3V≤VOUT<1.5V 200 mA 500 mA 4 1 10 6 mV mV 1100 1300 Dropout VoltageVDROP IOUT =500mA 1.5V≤VOUT<2V 900 1050 mV 500 700 2V≤VOUT<2.5V 2.5V≤VOUT<3.4V 280 380 55 65 dB PSRR Ripple Rejection F≤1kHz, 1Vpp at VIN = VOUT+1.0V µA IQ No load 50 100 Quiescent Current IOUT=500mA 370 450 Shutdown Supply (Note3)Current Shutdown = low IOUT=0, VCC =6.0V 0.01 1 µA µVrms 50 40 7 70 ms 100HzCopyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

4www.anpec.com.tw

APL5501/2/3

Electrical Characteristics

Symbol Parameter ISHDN Shutdown input Bias current(Note3)APL5501/2/3 Unit Test Conditions Min. Typ. Max. 0.01 100 nA 0.1 0.5 µA 11 50 mV VSHDN =VIN VOUT-VIN=0.1V Input Reverse Leakage current Reverse Protection Threshold Application Circuit

INPUT

2.7V to 6VVINAPL5501/2/3onoffSHDNGNDVOUTVOUT

BPCOUT4.7uFCIN1uFCBP0.1uFCopyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

5www.anpec.com.tw

APL5501/2/3

Typical Characteristics

32.5

APL5501/2/3-33Ground Pin Current vs. Load Current (uA)Current Limit vs. Input VoltageGround Pin Current vs. Output Current4003503002502001501005000

150

300

450

600

750

900

APL5501/2/3-33Current Limit (mA)21.510.503.5

4.5

5.5

Input Voltage (V)

Output Current (mA)

Ground Pin Current vs. Load Current (uA)Ground Pin Current vs. Input Voltage350300

APL5501/2/3-33Input Voltage vs. Output Voltage3.53

APL5501/2/3-33Output Voltage (V)2502001501005000

2.521.510.500

Input Voltage (V)Input Voltage (V)

6www.anpec.com.tw

APL5501/2/3

Typical Characteristics

Output Current vs. Output Voltage0APL5501/2/3-33Dropout Voltage vs. Output Current120011001000VOUT=1.5V-2Dropout Voltage (mV)90080070060050040030020010000100200300400500Output Current (uA)VOUT=1.8V-4-6-8-10-120

0.5

1.5

VIN=0VVOUT=3.3VVOUT=2.5V22.53

Output Current (mA)Output Voltage (V)

SHDN Threshold Voltage vs. Input Voltage1APL5501/2/3-33PSRR vs. FrequencyAPL5501/2/3-33+0-10-20SHDN Threshold Voltage (V)0.90.8PSRR (dB)VIN=0V-30-40-50-60-70VIN=4VIOUT =50mACOUT=10uFCBP=0.1uF0.70.60.5-80-90VIN=5V0.43

3.5

4.5

5.5

-10020501002005001k2k5k10k20k50k100k200kInput Voltage (V)Frequency (HZ)

7www.anpec.com.tw

APL5501/2/3

Typical Characteristics

Output Noise100uAPL5501/2/3-33Output Noise vs. Bypass Capacitor

500450400

VIN=4.3V80uIOUT =0mACOUT=10uF60uCBP=0.1uFVOUT (50uV/div)20u0-20u-40uOutput Noise (uV)02m4m6m8m10m40u3503002502001501005000

0.1

0.2

0.3

0.4

-80u-100uTime (s)Bypass Capacitor (uF)

Shutdown Exit Delay

APL5501/2/3-33

Shutdown Exit Delay

APL5501/2/3-33

3.3V

VOUT

CBP=10nFNo Load

4V4V

vSHDNCBP=100nFNo Load

vSHDN0V

Time (1ms/div)Time (20ms/div)

8www.anpec.com.tw

APL5501/2/3

Typical Characteristics

Entering Shutdown

APL5501/2/3-33

Region of Stable ESR vs. Load Current

APL5501/2/3-333.3V

VOUT

0.1

VOUT=3.3VCOUT=1µFNo Load

COUT ESR (Ω)0.01

stableunstable0V

0.001

150

300

450

600

750

900

Time (200ms/div)Load Current (mA)

Output Voltage vs. Temperature3.35

APL5501/2/3-33Line-Transient Response

APL5901/2-33

Output Voltage (20mV/div)3.33

VIN

4V3V

Output Voltage (V)3.31

3.29

VOUT

3.27

3.25

-40

120

Temperature (°C )

Time (40µs/div)

9www.anpec.com.tw

APL5501/2/3

Typical Characteristics

Load-Transient Response

APL5501/2/3-33

Output Voltage (50mV/div)VOUT

COUT=1µFVIN=VOUT+1V

IOUT=1mA~500mA

Time (10µs/div)

10www.anpec.com.tw

APL5501/2/3

Application Information

Capacitor Selection and RegulatorStability

The APL5501/2/3 use at least a 1uF capacitor on theinput, and this capacitor can be Aluminum, Tantalumor Ceramic capacitor. The input capacitor with largervalue and lower ESR provides better PSRR and line-transient response. The output capacitor also can useAluminum, Tantalum or Ceramic capacitor, and a mini-mum value of 1uF and ESR above 0.06Ω isrecommended. The curve of the stable region in typi-cal characteristics shows the appropriate output ca-pacitor ESR for different load current stable operation.A larger output capacitor can reduce noise and im-prove load-transient response, stability, and PSRR.Note that some ceramic dielectrics exhibit large ca-pacitance and ESR variation with temperature. Whenusing this capacitor, a minimum 10uF or more maybe required to ensure the stability at low temperatureoperation. Use a bypass capacitor at BP pin for lowoutput nvise. Increasing the capacitance will slightlydecrease the output noise, but increase the start-uptime.

end-of-life battery voltage. Because the APL5501/2/3use a p-channel MOSFET pass transistor, the drop-out voltage is a function of drain-to-source on-resis-tance (RDS(ON)) multiplied by the load current.

Reverse Current Protection

The APL5501/2/3 have an internal reverse protection,it does not need an external schottky diode to con-nect the regulator input and output. If the output volt-age is forced above the input voltage by more than11mV, the IC will be shutdown and the ground pincurrent is below 0.1uA.

Shutdown/Enable

The APL5501/2/3 have an active high enable function.Force EN high (>1.6V) enables the regulator, EN low(<0.4V) disables the regulator and enter the shutdownmode. In shutdown mode, the quiescent current canreduce below 1uA. The EN pin cannot be floating, afloating EN pin may cause an indeterminate state onthe output. If it is no use, connect to VIN for normaloperation.

Load-Transient Considerations

The APL5501/2/3 load-transient response graphs intypical characteristics show the transient response.A step change in the load current from 0mA to 500mAat 1us will cause a 100mV transient spike. Largeroutput capacitor and lower ESR can reduce transientspike.

Current Limit

The APL5501/2/3 have a current limit protection. Theouptut voltage will drop close to zero volt, when loadcurrent reaches the limit, and then the load currentwill be limited at 150mA after output voltage is below0.7V. When the load current back to the value wherelimiting started, the output voltage and current will re-turn to normal value. When output is shorted toground, the APL5501/2/3 will keep short circuit cur-rent at 150mA .

www.anpec.com.tw

Input-Output (Dropout)Voltage

The minimum input-output voltage difference (dropout)determines the lowest usable supply voltage. In bat-tery-powered systems, this will determine the useful

APL5501/2/3

Thermal Protection

Thermal protection limits total power dissipation in thedevice. When the junction temperature exceeds

¢J, the thermal sensor generates a logic sig-TJ=+150¢J

nal to turn off the pass transistor and allows IC tocool. When the IC’s junction temperature is down by¢J10¢J, the thermal sensor will turn the pass transistoron again, resulting in a pulsed output during continu-ous thermal protection. Thermal protection is designedto protect the APL5501/2/3 in the event of faultconditions. For continuous operation, do not exceedthe absolute maximum junction temperature ofTJ=+150¢J.¢J

Operating Region and Power Dis-sipation

The thermal resistance of the case to circuit board,and the rate of air flow all control the APL5501/2/3’smaximum power dissipation. The power dissipationacross the device is PD = IOUT (VIN-VOUT) and the maxi-mum power dissipation is:PDMAX = (TJ-TA) / (£c£cJC +£c£cCA)

where TJ-TA is the temperature difference between the

£cJC is the thermal resis-junction and ambient air, £ctance of the package, and£c£cCA is the thermal resis-tance through the printed circuit board, copper traces,and other materials to the ambient air.

The GND pin of the APL5501/3 provide an electricalconnection to ground and channeling heat away. Ifpower dissipation is large, connect the GND pin toground using a large pad or ground plane, can im-prove the problem of over heat of IC.

12www.anpec.com.tw

APL5501/2/3

Packaging Information

SOT-23-5

e1E1E123ebDA2AaL 1A1L 2LDimAA1A2DEE1LL1L2NαMillimetersMin.0.950.050.902.82.61.50.350.20 BSC0.550°10°0°0.70.020Max.1.450.151.303.003.001.700.55Min.0.0370.0020.0350.1100.1020.0590.014InchesMax.0.0570.0060.0510.1180.1180.0670.0220.008 BSC0.028510°Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

13www.anpec.com.tw

APL5501/2/3

Packaging Information

SOP-8 pin ( Reference JEDEC Registration MS-012)

EHe1De2A1A1L0.004max.DimAA1DEHLe1e2φ1MillimetersMin.1.350.104.803.805.800.400.331.27BSC8°Max.1.750.255.004.006.201.270.51Min.0.0530.0040.10.1500.2280.0160.0130.015X45InchesMax.0.0690.0100.1970.1570.2440.0500.0200.50BSC8°Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

14www.anpec.com.tw

APL5501/2/3

Packaging Information

SOT-223( Reference JEDEC Registration SOT-223)

DB1AcaHELKee1bA1BDimAA1BB1cDEee1HLKαβMin.1.500.020.602.900.286.303.30MillimetersMax.1.800.080.803.100.326.703.702.3 BSC4.6 BSC6.700.911.500°13°15

InchesMin.0.060.020.110.010.250.130.09 BSC0.18 BSC7.301.102.0010°0.260.040.060°13°www.anpec.com.tw

Max.0.070.030.120.010.260.150.290.040.0810°Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

APL5501/2/3

Packaging Information

SOT- (Reference EIAJ ED-7500A Reg stration SC-62)

DD1aHE123LB1ee1CBAaDimABB1CDD1ee1EHLαMillimetersMin.1.400.400.350.3.401.351.50 BSC3.00 BSC2.293.750.802.604.251.2010°0.0900.1480.031Max.1.600.560.480.444.601.83Min.0.0550.0160.0140.0140.1730.053InchesMax.0.0630.0220.0190.0170.1810.0720.059 BSC0.118 BSC0.1020.1670.04710°Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

16www.anpec.com.tw

APL5501/2/3

Packaging Information

SOT--5

DimABCDEFGHIJKLMillimetersMin.4.404.051.501.302.400.803.00 REF1.50 REF0.401.400.355 TYP0.521.600.410.010.050.01Max.4.604.251.701.502.60-Min.0.170.160.060.050.090.03InchesMax.0.180.170.070.060.1-0.12 REF0.06 REF0.020.060.020.2 TYPCopyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

17www.anpec.com.tw

APL5501/2/3

Packaging Information

TO-252( Reference JEDEC Registration TO-252)

Eb2L2AC1DHL1Lbe1CA1DimAA1bb2CC1DEe1HLL1L2MillimetersMin.2.180.0.5085.2070.460.465.3346.353.969.3980.510.0.1.022.03218

InchesMax.2.391.270.5.4610.580.586.226.735.1810.41Min.0.0860.0350.0200.2050.0180.0180.2100.2500.1560.3700.0200.0250.0350.0400.080www.anpec.com.tw

Max.0.0940.0500.0350.2150.0230.0230.2450.2650.2040.410Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

APL5501/2/3

Packaging Information

TO-252-5

ABHJMDCLSPKDimABCDPSHJKLMMillimetersMin.6.405.206.802.201.27 REF0.502.200.4500.905.400.802.400.550.151.505.800.020.080.0100.030.21Max.6.805.507.202.80Min.0.250.200.260.08InchesMax.0.260.210.270.110.05 REF0.030.090.020.0060.060.22Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

19www.anpec.com.tw

APL5501/2/3

Physical Specifications

Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow)

Ramp-uptpCritical ZoneTL to TP TemperatureTL

TsmaxtLTsminRamp-downtsPreheat25

° t 25 C to PeakTime

Classificatin Reflow Profiles

Profile Feature Sn-Pb Eutectic Assembly Large Body Small Body Pb-Free Assembly Large Body Small Body Average ramp-up rate 3°C/second max. 3°C/second max. (TL to TP) Preheat - Temperature Min (Tsmin) 100°C 150°C - Temperature Mix (Tsmax) 150°C 200°C - Time (min to max)(ts) 60-120 seconds 60-180 seconds Tsmax to TL 3°C/second max - Ramp-up Rate Tsmax to TL - Temperature(TL) 183°C 217°C - Time (tL) 60-150 seconds 60-150 seconds Peak Temperature(Tp) 225 +0/-5°C 240 +0/-5°C 245 +0/-5°C 250 +0/-5°C Time within 5°C of actual Peak 10-30 seconds 10-30 seconds 10-30 seconds 20-40 seconds Temperature(tp) Ramp-down Rate 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Time 25°C to Peak Temperature Note: All temperatures refer to topside of the package. Measured on the body surface. Copyright  ANPEC Electronics Corp.

Rev. B.1 - Mar., 2004

www.anpec.com.tw

APL5501/2/3

Reliability test program

Test itemSOLDERABILITYHOLTPCTTSTESDLatch-UpMethodMIL-STD-883D-2003MIL-STD-883D-1005.7JESD-22-B, A102MIL-STD-883D-1011.9MIL-STD-883D-3015.7JESD 78Description245°C , 5 SEC1000 Hrs Bias @ 125 °C168 Hrs, 100 % RH , 121°C-65°C ~ 150°C, 200 CyclesVHBM > 2KV, VMM > 200V10ms , Itr > 100mACarrier Tape

tPP1DPoEFWBoAoKoD1T2JCABT1Copyright  ANPEC Electronics Corp.Rev. B.1 - Mar., 2004

21www.anpec.com.tw

APL5501/2/3

Reel Dimensions

ApplicationA330 ± 1SOP- 8F5.5± 1ApplicationA178 ±1SOT-F5.5 ± 0.05ApplicationA330±1SOT-223F5.5 ± 0.05ApplicationA330 ±3TO-252F7.5 ± 0.1B62 +1.5D1.55 +0.1B70 ± 2D1.5± 0.1B62±1.5D1.5+ 0.1B 100 ±2D1.5 +0.1C12.75+ 0.15D11.55+ 0.25C13.5 ± 0.15D11.5± 0.1C12.75±0.15D11.5+ 0.1C 13± 0. 5D11.5± 0.25J2 ± 0.5Po4.0 ± 0.1J3 ± 0.15Po4.0 ± 0.1J2 ± 0.6Po4.0 ± 0.1J2 ± 0.5Po4.0 ± 0.1T112.4 ± 0.2P12.0 ± 0.1T114 ± 2P12.0 ± 0.1T112.4 +0.2P12.0 ± 0.05T116.4 + 0.3 -0.2P12.0 ± 0.1T22 ± 0.2Ao6.4 ± 0.1T21.3 ± 0.3Ao4.8 ± 0.1T22± 0.2Ao6.9 ± 0.1T22.5± 0.5Ao6.8 ± 0.1W12± 0. 3Bo5.2± 0. 1W12 + 0.312 - 0.1Bo4.5± 0.1W12 ± 0.3Bo7.5± 0.1W16+ 0.3 - 0.1Bo10.4± 0.1P8± 0.1Ko2.1± 0.1P8 ± 0.1Ko1.80± 0.1P8 ± 0.1Ko2.1± 0.1P8 ± 0.1Ko2.5± 0.1E1.75±0.1t0.3±0.013E1.75± 0.1t0.3±0.013E1.75± 0.1t0.3±0.05E1.75± 0.1t0.3±0.05(mm)Cover Tape Dimensions

ApplicationSOP- 8SOT- SOT- 223TO- 252Carrier Width12121216Cover Tape Width9.39.39.313.3Devices Per Reel2500100025002500Customer Service

Anpec Electronics Corp.Head Office :

5F, No. 2 Li-Hsin Road, SBIP,Hsin-Chu, Taiwan, R.O.C.Tel : 886-3-52000Fax : 886-3-52050

Taipei Branch :

7F, No. 137, Lane 235, Pac Chiao Rd.,

Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.Tel : 886-2-191368Fax : 886-2-191369

22www.anpec.com.tw

因篇幅问题不能全部显示，请点此查看更多更全内容

查看全文